Differences

This shows you the differences between two versions of the page.

--- makerbot [2022/04/18 05:58] – Fixed Bullet points showing in a row braeden.leislar
+++ makerbot [2022/07/17 03:13] (current) – swalde
@@ Line 1: / Line 1: @@
 ====MakerBot Replicator 2====
-Link: to printer server [[http://octoprintserver.int.sktw.ca:5000]], this link only works at Techworks.
+Link: to printer server [[http://octoprintserver.int.sktw.ca:5000]], this link only works at Techworks. (Link currently does NOT work. Use the SD card method below.)
-This printer is a classic in the shop. Its a 2012 printer with a print volume 285x153x155mm.
+This printer is a classic in the shop. Its a 2012 printer with a print volume 285x153x155mm.  It is configured to print with PLA only.
+You **MAY NOT** leave this printer unattended.  It lacks the safety mechanisms of newer printers and //has// destroyed itself in the past.
+==Loading or Changing Filament==
+To unload filament that is currently loaded in the printer, use the arrow keys on the printer to find "Utilities"->"Change Filament"->"Unload".  Wait for the extruder to heat up and follow the instructions on the screen.  Once the filament is out of the extruder, pull it back through the feed tube, remove the spool from the back of the printer, and store the spool properly.
+To load new filament, place the spool on one of the spool holders on the back of the printer.  Ensure that the filament is not tangled on the spool and that it comes off the bottom of the spool towards the feed tube. (It //will// jam if you do it the other way.)  If it's not already, pull the feed tube straight up out of the extruder.  Feed the filament through the feed tube until it emerges near the print head.  Using the arrow keys find "Utilities"->"Change Filament"->"Load".  Wait for the extruder to heat up and follow the instructions on the screen.  Once the filament is feeding properly, make sure to insert the feed tube back into the top of the extruder.
 ==Printing==
@@ Line 9: / Line 17: @@
 To print using this printer you must first download and install [[http://support.makerbot.com/s/article/Download-MakerBot-Desktop|MakerBot Desktop]].
-Launching the application you will be greeted with a virtual view of the print bed. Drag and drop your STLs into the view space. Your model can be adjusted using the scale, move, and rotate tools on the left. Once your happy with your print you can click on preview in the top right to view the sliced print. From the preview screen you can export. If you are uploading to the print server you must export as gcode. If you are printing with a SD card you must export as a x3g file.
+Launching the application you will be greeted with a virtual view of the print bed. Drag and drop your STLs into the view space. Your model can be adjusted using the scale, move, and rotate tools on the left. Once you're happy with your print you can click on preview in the top right to view the sliced print. From the preview screen you can export. If you are uploading to the print server you must export as gcode. If you are printing with a SD card you must export as a x3g file.
-Check that the printer bed is clear of any preview prints and plastic debris before starting your print
+Check that the printer bed is clear of any previous prints and plastic debris before starting your print.
 ==Printing from Server==
@@ Line 18: / Line 26: @@
 Once logged in, check the connection status on the top left. If the printer is not connected set the Serial Port to "/dev/tty/ACM0", the Baudrate to 115200, and the profile to Replicator 2 then click connect.
-To upload files to the printer simply drag and drop your files onto the left side of the browser or use the upload bottom and locate your files. Your file should appear in the file viewer. To print click on the title of your file, the details will appear under the "State" section. Once ready hit print.
+To upload files to the printer simply drag and drop your files onto the left side of the browser or use the upload button and locate your files. Your file should appear in the file viewer. To print, click on the title of your file. The details will appear under the "State" section. Once ready hit print.

makerbot.1650261538.txt.gz · Last modified: 2022/04/18 05:58 by braeden.leislar

Back to top