Differences

This shows you the differences between two versions of the page.

--- smtstencil [2014/05/10 03:46] – srw7
+++ smtstencil [2020/11/04 18:02] (current) – swalde
@@ Line 19: / Line 19: @@
 Carefully place all SMT components on the board.  Then "bake" the board in the reflow oven.  Our oven is pre-set for a Tin-Lead profile.  Plug it in. Place your board as near the centre of the oven as possible, then press the right button.  At the peak temperature, once the heat turns off, open the door to allow faster cooldown.  Watch the temperature! It's too hot to handle for longer than you might think.
+----
+Erik's smt stencil etching method
+(more involved, but optimized for quicker etching time)
+Steps 1-6 as before
+  - select all→right click→clone→3columns,1row
+  - select Leftmost board, edit width to be 0.1mm (toolbar on the left) (make sure "lock" aspect ratio is OFF)
+  - same as above, but with Rightmost board
+  - select all→right click→Scatter Group
+  - select all→right click→fill, Direction: X Double, 508, 0, CHECK “Delete Contours”, OK
+  - zoom in to a small pad to check dpi setting - if lines are too far apart to get all the detail, increase scan dpi - if dpi is very high, it will take longer to etch
+  - if you decreased the dpi you may have to unfocus the laser and increase the power
+  - set velocity to 800 (it will go as fast as it can) and power to 30%
+  - carve out
+----
+==Gerber to DXF (New, even more complicated workflow)==
+Okay, but I have a Gerber file (that someone gave me, so, no, I can't re-export from Eagle/KiCAD) and your laser takes DXF and I can't find a free Gerber to DXF converter.  What do I do?
+Simple!  (Not really, but it seems to work)
+  - Open the GTP file in Gerbv
+  - Export as PNG, 1016 dpi (this is arbitrary and is a leftover from a previous attempted workflow)
+  - Load PNG into GIMP
+  - Set DPI in Image->Print Size.  Take note of dimensions in mm
+  - Colour->Invert
+  - Colour->Threshold (about 3/4)
+  - Select->By Colour, click black
+  - Select->Shrink Selection (5 seems to be good)*
+  - New Layer, white background
+  - Fill (whole selection) with black
+  - delete original layer
+  - Export as PNG
+  - Load PNG into Inkscape
+  - Trace Bitmap
+  - delete bitmap
+  - Note dimensions in mm
+  - save as DXF
+  - Load into Smartcarve
+  - Set the dimensions
+*
+  - New possible process from here? (avoids having to "trace" again in inkscape)
+  - In The Gimp, choose Selection->To Path.
+  - Open the paths dock.  Right-click on the path and choose "export"
+  - Name the SVG file to export.
+==Gerber to DXF (This one failed with 45 degree rounded-end pads. gerbv totally screwed up the export)==
+Okay, but I have a Gerber file (that someone gave me, so, no, I can't re-export from Eagle/KiCAD) and your laser takes DXF and I can't find a free Gerber to DXF converter.  What do I do?
+Simple!  (Not really, but it seems to work)
+I did this all on Linux, so if things work different on Windows, please let me know.
+Use **gerbv** to open the gerber file.  Look at it.  Use the Measure tool to measure some easy-to-repeat dimension.  Write that down.  In **gerbv**, there is an export option.  Export the file as SVG.
+Open that SVG file in **Inkscape**.  Save it as a "Desktop Cutting Plotter (AutoCAD DXF R14) (*.dxf)" file.  (My Inkscape had a different DXF option, but it didn't work for this.)  On the dialogue that pops up, make sure to select "mm" as your base unit.  I also used LWPOLYLINE line output.
+Now, open that DXF in **LibreCAD**. (This step might not be necessary, but follow along for now.)  Remember that dimension I asked you to measure?  Measure it again.  For some reason, whenever I do this, my drawing ends up at exactly 80% scale.  Scale it up by a factor of 1.25.  Save it.  Now, take that file to the laser.  (You could probably do the scale in SmartCarve if you know, for a fact, that it's out by that factor.  I used LibreCAD here because I knew I could use the dimension tool better than in SmartCarve.)

smtstencil.1399693619.txt.gz · Last modified: 2014/05/10 03:46 by srw7

Back to top